(v 1.1)
To check and download all versions of this guide, go at the following link.
Safety and usage cautions
Before installing our products, we recommend you to consult the section about safety and usage cautions at the link below.
Mounting
To set display orientation click here.
For mounting, click here.
Wiring
For all wiring, old electronic cards must be eliminated
Serial DMG D67 -> Giotto D6
Other Controllers D67 -> Giotto D6
Floor
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
The new TFT displays have menu-programmable inputs. Therefore always start connecting the position wires starting from the lowest floor in the X01 input of the TFT display and the others in the following inputs, then adjusting the offset. For example, starting from floor -1, wire as below and set the offset to -1
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
Other Controllers D45 -> Raffaello D4
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
It’s possible to customize service message inputs via specific menu (click here)
The new TFT displays have menu-programmable inputs. Therefore always start connecting the position wires starting from the lowest floor in the X01 input of the TFT display and the others in the following inputs, then adjusting the offset. For example, starting from floor -1, wire as below and set the offset to -1
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
It’s possible to customize service message inputs via specific menu (click here)
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
It’s possible to customize service message inputs via specific menu (click here)
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
It’s possible to customize service message inputs via specific menu (click here)
Serial DMG D43 -> Raffaello D4
Other Controllers D43 -> Raffaello D4
Floor
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
The new TFT displays have menu-programmable inputs. Therefore always start connecting the position wires starting from the lowest floor in the X01 input of the TFT display and the others in the following inputs, then adjusting the offset. For example, starting from floor -1, wire as below and set the offset to -1
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables C – D – E – F will be wired on the arrows. Therefore will not have to be wired to the Display
Serial DMG D13 -> Raffaello D1
Other controller
Other Controllers D13 -> Raffaello D1
In case of Display + Arrows, cables B – C – D – E will be wired on the arrows. Therefore will not have to be wired to the Display
The new TFT displays have menu-programmable inputs. Therefore always start connecting the position wires starting from the lowest floor in the X01 input of the TFT display and the others in the following inputs, then adjusting the offset. For example, starting from floor -1, wire as below and set the offset to -1
In case of Display + Arrows, cables B – C – D – E will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables B – C – D – E will be wired on the arrows. Therefore will not have to be wired to the Display
In case of Display + Arrows, cables B – C – D – E will be wired on the arrows. Therefore will not have to be wired to the Display
Settings
 Setup Key |  Exit / Back |  Access Menu Key |  Value setting (>3 sec.) |
D67 -> Giotto D6
The display navigation menu is in English only; to see the correct menu items we recommend setting the DIDO website language to English.| MENU | MENU ITEM | AVAILABLE CHOICES | INPUTS | |||
|---|---|---|---|---|---|---|
| Serial / Pitagora | Parallel | CANBUS | ||||
| Input | Serial / 1 wire per floor / segment Gray / Binary / Pos.Sensor TKE / MEA / Autinor / CAN DMG | • | • | • | ||
| Audio Settings | Volume (Gong, floor message, etc.) | 0-OFF / 1-MIN / 2 / 3 / 4-MAX | • | • | • | |
| Trigger Delay | 0, 1, ..., 30 | • | • | • | ||
| Message Sequence | Gong - Floor - Up/Down | • | • | • | ||
| Options | Interface Options | Display Configuration | COP / LOP / LIP | • | • | • |
| Arrow Configuration | Direction / Next Dir. | • | ||||
| Car at Floor | No / Yes | • | • | |||
| Gong with NO Arrows | No / Yes | • | ||||
| CAN Baudrate | 250k, 125k, 10k, Auto | • | ||||
| Convert Mezzanine | No / Yes | • | ||||
| Offset Value | -9 / ... / 0 / ... / +9 | • | ||||
| First Visualization | Blank / Zero | • | ||||
| Common Selection | Negative / Positive | • | ||||
| Arrow Type | Fixed arrows / Scrolling arrows | • | ||||
| Enable AUX Signals | 10 + 0 / 6 + 4 | • | ||||
| Input Filtering | 0 ... 20 | • | ||||
| Gong from Arrows | No / Yes | • | ||||
| Firefighters Operation | 0 (Disabled) / 1 (Egress Floor) / 2 (Non-Egress Floor) | • | • | • | ||
| Screensaver timer | Disabled / 10-20 / 30-60 / 60-120 | • | • | • | ||
| Graphic Options | Floor Symbols | Show / Hide | • | • | • | |
| Arrows | Show / Hide | • | • | • | ||
| Floor Symbols with Signals | Show / Hide | • | • | • | ||
| Arrows with Signals | Show / Hide | • | • | • | ||
| Auto Centering | No / Yes | • | • | • | ||
| Numbers alignment | Center / Left / Right | • | • | • | ||
| Kerning | No / Yes | • | • | • | ||
| Filter Blinking Signals | No / Yes | • | • | • | ||
| Orientation | Landscape / Portrait | • | • | • | ||
| S1-S5 inputs Configuration | Input S1 / ... / S5 | • | • | • | ||
| AUX Signals Configuration | AUX Signal 1 / 2 / 3 / 4 | • | • | • | ||
| Info Screen | On / Off | • | • | • | ||
| Info Screen Tme | 5s / 10s / 15s / 20s | • | • | • | ||
| Date & Time Settings | No / Yes | • | • | |||
| Reset All Settings | • | • | • | |||
| USB | Display -> USB / USB -> Display | • | • | • | ||
| Aggiornamento firmware / Firmware update | • | • | • | |||
| ? | DEMO mode | No / Yes | • | • | • | |
| Firmware Ver. / Config. Name / Debug Mode / Life Time (internal use) | • | • | • | |||
| Floor Settings | Floor Image | Choose the Images | • | • | • | |
| Floor Audio | No / Audio slot 0 / ... / slot 19 | • | • | • | ||
| Floor Symbols | Choose the Symbols | • | ||||
For all settings of the new Giotto display, click the following link.
D45 -> Raffaello D4
For all settings of the new Raffaello display, click the following link.
D43 -> Raffaello D4
For all settings of the new Raffaello display, click the following link.
D13 -> Raffaello D1
For all settings of the new Raffaello display, click the following link.
Download
| Reference | Version | Link |
|---|---|---|
| 1.0 | Download PDF (English) | |
| Retrofit D45 and D13 added | 1.1 (current version) | Download PDF (English) |
