2″ RAFFAELLO Display

The display navigation menu is in English only; to see the correct menu items we recommend setting the DIDO website language to English.

MENU	MENU ITEM			AVAILABLE CHOICES	INPUTS
					Parallel	CANBUS
Input				Serial / 1 wire per floor / segment Gray / Binary / Pos.Sensor TKE / MEA / Autinor / CAN DMG	•	•
Options	Interface Options	Arrow Configuration		Direction / Next Dir.		•
		Car at Floor		No / Yes		•
		CAN Baudrate		250k, 125k, 10k, Auto		•
		Convert Mezzanine		No / Yes		•
		Offset Value		-9 / ... / 0 / ... / +9	•
		First Visualization		Blank / Zero	•
		Common Selection		Negative / Positive	•
		Arrow Type		Fixed arrows / Scrolling arrows	•
		Enable AUX Signals		10 + 0 / 6 + 4	•
		Input Filtering		0 ... 20	•
		Screensaver timer		Disabled / 10-20 / 30-60 / 60-120	•	•
	Graphic Options	Font		Dado / Classic Bold / Lagoon / Dot Matrix	•	•
		Flat Style	Symbol color	White / Red / Orange / Blue / Gray / Black	•	•
			Background color	Black / Pacific Blue / Navy Blue / Reef Blue / Light Gray /White / Orange / Red	•	•
			Specials	White-Green / White-Lilac / Purple-Yellow / White-Gray	•	•
		Gradient Style	Style	Black & White / Red Passion / Gray Goose / Blue Shades	•	•
			Color	Galaxy / Ocean Dream 2/1 / Reef Blue / Purple haze / ...	•	•
		Floor Symbols		Show / Hide	•	•
		Arrows		Show / Hide	•	•
		Fixed Symbols Positions		No / Yes	•	•
		Filter Blinking Signals		No / Yes	•	•
		Message Mode Orientation		Alternating / Fixed	•	•
		Orientation		Landscape (Horiz.) / Portrait (Vert.) / Rev.Landscape / Rev.Portrait	•	•
		Signal Inputs Configurations	Input S4		•	•
		AUX Signals Configurations		AUX Signal 1 / 2 / 3 / 4	•	•
	Reset All Settings				•	•
?	DEMO mode			No / Yes	•	•
	Firmware Version / Life Time (internal use)				•	•
Floor Numbers	Numbers / Letters			Choose the Numbers / Letters	•

1) – Direction arrows (default)
2) – Next direction arrows (instructions below)


Next Direction Arrows enabled from input
Arrows light up only on the position indicators with the “NEXT DIRECTION” input powered.If the DEUM Encoder is used, please refer to the relevant manual

Next Direction Arrows locally programmed
Through the addressing procedure one can permanently assign to each indicator the information of the floor on which it is mounted; in this way, next direction arrows only light up at the floor where the elevator car is positioned.

– Addressing procedure

1) – Connect all position indicators to the ENCODER or PLAYBOARD controller.
2) – Position elevator car on the floor of the Display which needs to be directed.
3) – Verify that the characters/numbers/letters visualized are the desired ones.
4) – Press and hold the ADV key and wait for the display to flash for 3 seconds to confirm.
5) – Repeat procedure for each floor.If the DEUM Encoder is used, please refer to the relevant manual

The parameter allows to assign the display (floor) to a unique controller. The Duplex-Light typology includes 2 controllers with a single BDU line and a maximum of 2 displays at the main floor.
This parameter can only be set with the CAN protocol on the Pitagora 4.0 system.0) – To be associated with the lift car position indicator.
1) – The display will show the information of the MASTER controller.
2) – The display will show the information of the SLAVE controller.
3/4/5/6) – Future uses.

The display original factory settings will be restored and configurations will be deleted.